Covered Outdoor Space That Stays Dry
Covered patio construction in Bardstown for older homes where the rear structure was never designed for a roof
Many older Bardstown homes were built without any provision for a covered outdoor space at the rear—no structural attachment point, no footer, and a roofline that makes adding a covered patio a more involved decision than it looks from the outside. All & All Construction & Dumpsters LLC builds covered patios attached to existing homes and as stand-alone structures, handling the footings, framing, roofing, and concrete slab with a single five-person in-house crew. Small-town lots with tight back yards require that sizing, attachment point, and setback all get worked out before materials are ordered.
The crew begins by measuring the setback from property lines and identifying the attachment point on the house. Footings are set below the frame line before any framing goes up, which keeps the structure from shifting as the ground moves through load changes. Posts and beams are framed next, then roof decking and roofing are installed, with flashing applied carefully where the new roof meets the existing house wall. If a concrete slab is part of the project, it is poured and allowed to cure before framing begins so the structure bears on finished concrete rather than fresh material.
Schedule a free estimate so the crew can measure the attachment point, confirm setback requirements for your lot, and give you a specific plan before any work is committed.
Why the Attachment and Flashing Details Drive the Outcome
A covered patio attached to a house creates one critical intersection that determines whether the structure stays dry or introduces a leak: the line where the new roof meets the existing wall. Flashing at that joint has to be installed under the existing siding and over the new roofing in the correct order, with no gaps at the ends where water can track sideways along the flashing edge. Getting that sequence wrong produces a leak that is difficult to locate because the water enters at the roofline and travels down the wall before appearing at ceiling or floor level inside the house.
Once the patio is finished, you should be able to stand under the cover during rain and see water shed completely off the roof edge rather than tracking back toward the house. The attachment point should show no visible gap between the new structure and the existing siding, and the slab surface should slope gently away from the house so water drains outward. All & All Construction & Dumpsters LLC backs the installation with a one-year workmanship warranty that covers how the structure was built and how the flashing was integrated.
Stand-alone covered patios that are not attached to the house follow the same footing and framing sequence but skip the wall flashing entirely, which simplifies the build and eliminates the house-connection risk. The choice between attached and stand-alone depends on the yard layout, the setback available, and how the homeowner plans to use the space, all of which the crew works through during the estimate visit.
Common Questions About This Service
Covered patio projects raise consistent questions about sequencing and what the crew is responsible for at each stage. The answers below reflect how All & All Construction & Dumpsters LLC approaches these builds in Bardstown.
Why is the concrete slab poured before framing rather than after?
Fresh concrete continues to cure and settle for weeks after the pour. Setting posts and beams on cured concrete means the structure has a stable, finished base rather than one that is still gaining strength and could allow slight movement at post bases during the early framing stages.
How are footings sized and positioned for a covered patio?
Footing depth and diameter depend on the load the roof and framing will put on each post. The crew determines footing size during the site visit based on the planned structure, and footings are dug and poured before any above-grade framing begins.
What makes flashing at the house connection the most critical part of an attached patio build?
That joint is the only place where two independently built roof systems meet. Water that finds a gap at the flashing does not exit at the gap—it travels along the framing inside the wall and shows up as a stain or wet spot several feet away, making the source difficult to identify without removing finish material.
How does a tight back yard in Bardstown affect how a covered patio is sized?
Setback requirements from property lines, existing structures like sheds or fences, and the position of the rear door or window all constrain how deep and wide the patio can run. Those measurements are confirmed on the first site visit so the design fits the actual yard rather than a best-guess estimate.
What roofing material is used on a covered patio, and how is it matched to the house?
The roofing material is matched to the existing house roof where possible for visual consistency. Shingle type and color are confirmed before the estimate is finalized so materials are ordered correctly and arrive before the framing crew is ready for roof decking.
All & All Construction & Dumpsters LLC also builds covered patios in Bloomfield, New Hope, Fairfield, Springfield, and Shepherdsville. To begin with a free on-site estimate for your covered patio, call All & All Construction & Dumpsters LLC at (502) 510-4288.